Equipment is designed for measuring concentration of solid particles in air/gas and also for determination of combustion gas composition.
Thermal analysis of materials with evolved gas analysis by FTIR and GCMS methods.
Determination of heating value of biofuel, mixtures and calorific waste for determination of suitability of combustion in industrial furnaces.
Applicable for combustion process diagnostics, analysis of other fast processes where optical sensitivity is necessary.
Used for the analysis of the products from biofuel thermal destruction (gasification) and combustion.
Solid fuel and high-calorie waste sample preparation for supply them to the analytical instruments and making suitable working conditions for samples mineralization.
The system is intended to use in studies of biofuel combustion efficiency.
For various biomass pellets combustion parameters and emissions studies.
Studies of gasification process of solid recovered fuels, i.e., separation of synthesized gas phase in the reactor and subsequent determination of the gas parameters and its application.
To visualize ash melting state and analyze conditions to get information about ash softening, melting processes, depending on the temperature or its gradient values changes.
The influence of the humidity of air supplied for combustion on combustion process efficiency.
Studies on measurement accuracy of air humidity sensors.
Studies on fluid and gas dynamics at low speeds near the surface of the membrane and various trace elements, surface fouling.
The calorific analysis of natural, pyrolysis, liquefied petroleum gas, biogas and gas mixtures.
Heat flow visualization and measurement.
Combustion analysis of heating equipment (boilers, fireplaces, etc.) fired with solid and liquid fuel at operation site.
Determination and analysis of ash content, volatile matter and volatile composition of biofuels and recovered fuels Analysis of materials state transitions.
Major and minor element analysis of liquid and solid organic and mineral compounds of biofuels and recovered fuel.
Solid and liquid fuels, including biofuels and recovered fuel samples weighing in fuel moisture and ash analysis.
Studies of the particles dynamics in liquid and gas flows and flows interaction with surfaces and flow round bodies in order to increase efficiency of combustion processes and water treatment in plants and as well as to model momentum and heat transfer processes.
Very small air (gas) flow measurement in small-diameter channels or streams flowing through membranes;
Air-gas (sample) volume measurements at various gas formation and quantitative characteristics of analysers.
Evaluation of fuel quality, prices, quantities of heat and, performance parameters of thermal equipment.
The preparation of solid and calorific waste and soft, hard, elastic and fibrous materials of 0,25 ÷ 20 mm fractions. Compression of crushed materials into suitable samples for analysis. Ensuring proper working conditions while mineralizing the samples. Preparation of deionised water for mineralization of samples.
The determination of the Cl, F, Br concentration in the fuel in order to assess possible environmental pollution with harmful elements and evaluation of fuel quality indicators.
Research of furnaces up to 25 kW fired with biofuel pellets.
Identification and analysis of upper and lower heating values of gaseous fuels, including biofuels and recovered fuels. Determination and analysis of upper and lower heating values of other calorific materials (eg sewage sludge, waste, etc.).
Measurement and visualization of heat flux from surfaces for determination of heat loss, its location, insulation efficiency.
Determination of fuel elements in order to assess the fuel quality indicators and possible environmental pollution with harmful elements.
Precise measurements of fuel humidity and ash content, assessment of fuel quality indicators and combustion rate.
The determination of the chemical elements C/H/N/S and O in the fuel, evaluation of its qualitative and quantitative indicators.
The determination of the upper and lower calorific values and analysis of solid and liquid fuels, including biofuels and recovered fuels.
The preparation of solid and calorific waste and soft, hard, elastic and fibrous materials of 0,25 ÷ 20 mm fractions. Compression of crushed materials into suitable samples for analysis. Ensuring proper working conditions while mineralizing the samples. Preparation of deionised water for mineralization of samples.
The determination of the Cl, F, Br concentration in the fuel in order to assess possible environmental pollution with harmful elements and evaluation of fuel quality indicators.
Research of furnaces up to 25 kW fired with biofuel pellets.
Identification and analysis of upper and lower heating values of gaseous fuels, including biofuels and recovered fuels. Determination and analysis of upper and lower heating values of other calorific materials (eg sewage sludge, waste, etc.).
Measurement and visualization of heat flux from surfaces for determination of heat loss, its location, insulation efficiency.
Determination of fuel elements in order to assess the fuel quality indicators and possible environmental pollution with harmful elements.
Precise measurements of fuel humidity and ash content, assessment of fuel quality indicators and combustion rate.
The determination of the chemical elements C/H/N/S and O in the fuel, evaluation of its qualitative and quantitative indicators.
The determination of the upper and lower calorific values and analysis of solid and liquid fuels, including biofuels and recovered fuels.
Equipment is designed for measuring concentration of solid particles in air/gas and also for determination of combustion gas composition.
Thermal analysis of materials with evolved gas analysis by FTIR and GCMS methods.
Determination of heating value of biofuel, mixtures and calorific waste for determination of suitability of combustion in industrial furnaces.
Applicable for combustion process diagnostics, analysis of other fast processes where optical sensitivity is necessary.
Used for the analysis of the products from biofuel thermal destruction (gasification) and combustion.
Solid fuel and high-calorie waste sample preparation for supply them to the analytical instruments and making suitable working conditions for samples mineralization.
The system is intended to use in studies of biofuel combustion efficiency.
For various biomass pellets combustion parameters and emissions studies.
Studies of gasification process of solid recovered fuels, i.e., separation of synthesized gas phase in the reactor and subsequent determination of the gas parameters and its application.
To visualize ash melting state and analyze conditions to get information about ash softening, melting processes, depending on the temperature or its gradient values changes.
The influence of the humidity of air supplied for combustion on combustion process efficiency.
Studies on measurement accuracy of air humidity sensors.
Studies on fluid and gas dynamics at low speeds near the surface of the membrane and various trace elements, surface fouling.
Manufacturer: Dantec Dynamics
The calorific analysis of natural, pyrolysis, liquefied petroleum gas, biogas and gas mixtures.
Combustion analysis of heating equipment (boilers, fireplaces, etc.) fired with solid and liquid fuel at operation site.
Determination and analysis of ash content, volatile matter and volatile composition of biofuels and recovered fuels Analysis of materials state transitions.
Major and minor element analysis of liquid and solid organic and mineral compounds of biofuels and recovered fuel.
Solid and liquid fuels, including biofuels and recovered fuel samples weighing in fuel moisture and ash analysis.
Studies of the particles dynamics in liquid and gas flows and flows interaction with surfaces and flow round bodies in order to increase efficiency of combustion processes and water treatment in plants and as well as to model momentum and heat transfer processes.
Manufacturer: Dantec Dynamics
Very small air (gas) flow measurement in small-diameter channels or streams flowing through membranes;
Air-gas (sample) volume measurements at various gas formation and quantitative characteristics of analysers.
Manufacturer: Sierra Instruments
Evaluation of fuel quality, prices, quantities of heat and, performance parameters of thermal equipment.
